|
|
Iscar Offers A Completely New Family Of Slitting Cutters Using Tang-Grip Technology And The Strength Of Sumo Tec Grades
Iscar at this time offers a family of high-performance slitting tools that couple the convenience and security of Tang-Grip clamping with the increased durability of the brand new Sumo Tec insert grades.
The concept, already established effective in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanied by a distinct hand tool, and are retained tightly in place without the need for clamps, upper jaws or set screws that can weaken the insert and impede chip flow. The pocket configuration utilizes cutting forces to keep the insert seated tightly in position, preventing any danger of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus longer pocket and insert life.
Iscar's Sumo Tec insert grades feature a specific post-coating treatment which extensively improves tool life and dependability.
Unveiled in late 2007, the completely new Sumo Tec treatment smooths the insert's coated surface to eradicate microscopic stress raisers, reduce heat and friction and increase chip flow. The result is enhanced toughness and resistance to chipping and built-up edge, all leading to greater tool lifespan. The golden-colored side on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters offer more teeth than Iscar's SGSF cutters, allowing higher feed rates.
Their greater rigidity leads to straighter, additional accurate cuts and lowered vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same assortment of inserts as Tang-Grip parting tools. Some other sizes will be added.
Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate beneath a Sumo Tec TiAlN PVD coating, delivering excellent resistance to impact loads and built-up edge. This grade is endorsed for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.
IC830, offering increased toughness for heavier parting & grooving including interrupted cuts. It is suited for all stainless steel and high temperature alloys.
IC908, a hard, fine-grain substrate with excellent chipping resistance, joined with a brand new Sumo Tec TiAlN PVD coating. It is ideal for nodular or grey cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades suited for stainless steel, high temperature alloys and other alloy steels. These grades are likewise suggested for interrupted cuts and heavy operations.
All Tangslit and Tang-Grip inserts are presented in J- or C-type chipformer geometries from Iscar.
Iscar Recently Releases Many Original Lines To Continue Their Family Of Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.
Iscar Adds Their Most Recent Innovations To A Extended Line Of Flourishing Hole Making Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
Cutting Edge End Mills Coming From Iscar Will Enhance Productivity While Shrinking Costs
Manufacturers and die & mold shops can banish chatter problems in numerous milling operations with Iscar's new Chatterfree end mills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the primary source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
A Few Of The Many Advancements In Carbide Inserts Coming From Iscar Over The Years
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.
Completely New Tools And Carbide Insert Shapes From Iscar To Better The Machining Method
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
Push Pull Testing For Highway Industry Supplying Calibrated Measuring Instruments. Mechanical Load Testing Methods For On Site Proof To Testing Requirements.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.
Commercial Water Heater- Which Is Perfect For Your Necessities
If you are in the market for a commercial water heater then consider what the needed application is and your overall cost to determine which is best for you. Since there are so many to choose from you may have to do some calculating in order to match the need.
Totally New Rover Manufacturing Jobs
Britain's economy is trying to recover from the impact caused by the global economic recession through new Land Rover manufacturing jobs.
|
More Articles
Blogroll
|
